New Poster
•
2 Messages
Flex setup problems
I got the Flex today and hooked it up. When I turn on the TV and Flex, I get the initial Welcome message (in three languages). When I insert the batteries in the X15 remote, I get the three quick blue blinks. But when I press the Voice button (like the remote instructions say), the remote LED blinks red and the Flex doesn't do anything. The Welcome message stays on the screen for several seconds, then the Flex shuts off and the screen goes blank. If I power off/on the Flex (by unplugging power), the same thing happens again. When I press any button on the remote when the Flex is on, the remote LED blinks red. I tried the remote reset sequence (entering 981) and the remote shows green. But whenever I try to setup the Flex, I am unable to get past the initial three language Welcome screen. At this point, I don't know if the problem is with the Flex or the remote. Any suggestions?
- John
Accepted Solution
Wtng4StarLnk
Regular Visitor
•
4 Messages
4 years ago
Actually used the same cable...Its just that the Flex can auto detect the xfi or Xfinity supplied equipment easily. Its the own router/modem is what makes it difficult to set up. but anyways it finally worked so i'm happy.
0
john_sa05271
New Poster
•
2 Messages
5 years ago
This is an update from the original post:
I somehow got it to work, I'm not sure how. There were two things that I did:
1. I found a button on the bottom of the Flex box, under the arrows. With the Flex powered on but no Welcome message on the screen, I held down the button for about 10 seconds. I didn't see anything change. Then I unplugged the power, plugged it back in, and held the button down for about 15 seconds while the Flex powered up. I didn't get the Welcome menu. I powered off and on again.
2. When powering off the Flex box, I also unplugged the HDMI cable.
After doing these things, I powered the Flex back on, while the Flex was showing the initial Welcome screen, take a battery out of the remote and put it right back, press Voice button numerous times, and I finally got to the next setup menu. I was able to get the Flex box setup correctly, and also installed the Peacock app, which also worked.
So, problem solved, somehow.
0
Wtng4StarLnk
Regular Visitor
•
4 Messages
4 years ago
Mine does'nt work even after leaving on for a week. Still stucks on Welcome screen. I even replaced the unit from xfinity store. Mine is non Xfinity provided router/modem (Although compatible per https://www.xfinity.com/support/devices/#auth). I even plugged in the ethernet cable. My router showes it assigned the ip (identified with mac address)
0
0
XfinityChad2
Official Employee
•
263 Messages
4 years ago
0
CCIrma1
Official Employee
•
909 Messages
4 years ago
Thanks for reaching out, Wtng4StarLnk. I am sorry to hear about your experience with your services. I would like to have the opportunity to assist you to complete the activation. I just send you a private message to go over a few activation questions.
0
MT30
New Poster
•
2 Messages
4 years ago
Picture showed the home screen for Flex but continuously blinked. After several google’s and no luck troubleshooting with the app it’d scan and say it’s ok I decided to try a different HDMI cable. As far as I know the one sent was new but this completely solved my problem. Afterward I paired the remote to tv and sound bars one step. Hope that helps somebody 😊
0
CCIrma1
Official Employee
•
909 Messages
4 years ago
HDMI cables are very delicate! it happened to me before. I am happy that you are enjoying your flex box now. If you happened to drive by a Comcast store, ask for another HDMI cable to have one as a backup. Please don't hesitate to post here if you experience any other service issues. Have a great weekend!
0
0
AndyB234
New Poster
•
1 Message
4 years ago
My flex box shows welcome for about ten seconds then the TV says no signal. I never get to lanuage select. Any suggestions?
0
0
Wtng4StarLnk
Regular Visitor
•
4 Messages
4 years ago
yes i bought a new router now that has a wps button. after paiting with wps. my router shows the box is connected. Still the screen goes blank after intially showing Welcome screen.
0
0
Wtng4StarLnk
Regular Visitor
•
4 Messages
4 years ago
0
MT30
New Poster
•
2 Messages
4 years ago
0
0
LBAngel
New Poster
•
1 Message
4 years ago
0
0
user_e51bd1
Visitor
•
4 Messages
3 years ago
New x1 box not connecting to tv. Tried different hdmi cable, called tech support, even ran LAN wire to box for stronger connection. Box comes on gives me welcome message and then blacks out, and tv screen continuously flips between “signal received, signal lost”. Replaced first box with new one and still having the same exact issue.
1
0
vandesa
New Poster
•
2 Messages
3 years ago
I had a similar issue, help scripts were useless. Technician came and said, some TV on HDMI 1 port have screen saver properties that are NOT compliable with the Flex box. He put it onto HMDI 4 and it worked just fine. Now why do the online help and call center have scripts that tell you to try that.
I switched the cables, and power codes, the device and the remote, but not the PORT. guess what, changing port solved the problem.
0
0